StudentShare
Contact Us
Sign In / Sign Up for FREE
Search
Go to advanced search...
Nobody downloaded yet

Vehicle Interior Noise Prediction by Using Experimental Methods and Analysis - Thesis Example

Cite this document
Summary
The paper "Vehicle Interior Noise Prediction by Using Experimental Methods and Analysis" states that in most of the results the simulated and the experimental curve graphs were similar in shape. This was an indication that the result which was obtained experiment was valid…
Download full paper File format: .doc, available for editing
GRAB THE BEST PAPER92.7% of users find it useful

Extract of sample "Vehicle Interior Noise Prediction by Using Experimental Methods and Analysis"

Download file to see previous pages

Figure 3.3 gives a summary of the coefficients of the fibre C1 results. It can be seen that the 2mm thick sample C1 has the lowest absorption at all, the frequencies. Double 10mm has the highest absorption when we consider only a frequency of up to about 2000Hz beyond which it is seen that the other samples have higher absorption except for the C1 sample whose absorption remains low through the experiment range frequency. In can also be seen that when we consider the frequency of up to 2000Hz the absorption from highest to lowest is double 10mm, double 5mm, 10mm, double 2mm, 5mm and then 2mm.Figure 3.3: C2 absorption coefficients curves 4.

2 Fibre C2 results 4.2.1 Absorption coefficient for single fibre C2 Figure 3.4 shows the absorption coefficient for fibre C 2 for three different thickness starting from 2mm (C2), 5mm and 10mm thickness. From the figure, it can be observed that the experimental values were higher than the simulated values for all the frequency range investigated. It can also be seen that as the sample becomes thicker the experimental results curve become smoother and that the deviation between experimental curves and simulated results curves become smaller.

  From the graphs it can be seen that for the 2mm sample the maximum absorption of close to 1 is reached at a frequency of about 5500Hz, for 5mm sample maximum is reached at about 2500Hz while in the 10mm maximum absorption of close to 1 is reached at about 2000Hz frequency.Figure 3.5: Absorption coefficient for single fibre C2 curves 4.2.2 Absorption coefficients for Double C2Figure 3.2 shows the results that involved using two pieces (double) of the fibre C1 sample.

The samples used in the three set up were 2mm, 5mm and 10mm respectively. From the first pair of graphs, it can be seen that the experimental values rose to a maximum of about 0.95 when the frequency rose to about 4500Hz. 

...Download file to see next pages Read More
Download file to see previous pages

In the case of Double 5mm the maximum about of about 0.90 was at about 2500Hz . For double 10mm the maximum absorption value is seen to low also at about 0.90 and arrived at a frequency of about 1800Hz. Figure 3.2 : Absorption coefficients for Double C1 curves 4.1.3 Comparison of C2 absorption coefficients Figure 3.3 gives the summary of the coefficients of the fibre C1 results. It can be seen that the 2mm thick sample C1 has the lowest absorption at all, the frequencies. Double 10mm has the highest absorption when we consider only a frequency of up to about 2000Hz beyond which it is seen that the other samples have higher absorption except for the C1 sample whose absorption remains low through the experiment range frequency.

In can also be seen that when we consider frequency of up to 2000Hz the absorption from highest to lowest is double 10mm, double 5mm , 10mm , double 2mm , 5mm and then 2mm. Figure 3.3: C2 absorption coefficients curves 4.2 Fibre C2 results 4.2.1 Absorption coefficient for single fibre C2 Figure 3.4 shows the absorption coefficient for fibre C 2 for three different thickness starting from 2mm (C2), 5mm and 10mm thickness. From the figure it can be observed that the experimental values were higher than the simulated values for all the frequency range investigated.

It can also be seen that as the sample becomes thicker the experimental results curve become smoother and that the deviation between experimental curves and simulated results curves become smaller. From the graphs it can be seen that for the 2mm sample the maximum absorption of close to 1 is reached at a frequency of about 5500Hz, for 5mm sample maximum is reached at about 2500Hz while in the 10mm maximum absorption of close to 1 is reached at about 2000Hz frequency. Figure 3.5: Absorption coefficient for single fibre C2 curves 4.2.2 Absorption coefficients for Double C2 Figure 3.

2 shows the results that involved using two pieces (double) of the fibre C1 sample. The samples used in the three set up were 2mm, 5mm and 10mm respectively. From the first pair of graphs it can be seen that the experimental values rose to a maximum of about 0.95 when the frequency rose to about 4500Hz. In the case of Double 5mm the maximum about of about 0.90 was at about 2500Hz. for double 10mm the maximum absorption value is seen to low also at about 0.90 and arrived at a frequency of about 1800Hz.

Figure 3.6 : Absorption coefficients for Double C2 curves 4.2.3 Comparison of C2 absorption coefficients In figure 3.7 the results of summary of the coefficients of the fibre C2 are given. It can be seen that the 2mm thick sample has the lowest absorption considering all frequencies. Double 10mm has the highest absorption when we consider only a frequency of up to about 1300Hz beyond which it is seen that the other samples start having higher frequency and at about 4000Hz the double 10mm has the lowest absorption.

In can also be seen that when we consider frequency of up to 1300Hz the absorption from highest to lowest is double 10mm, double 5mm , 10mm , double 2mm , 5mm and then 2mm. Figure 3.7: C2 absorption coefficients curves 4.3 Fibre C3 results 4.3.1 Absorption coefficient for single fibre C3 Figure 3.4 shows the absorption coefficient for fibre C 3 for samples with thickness from 2mm (C2) , 5mm and 10mm . It can be seen that the experimental values are above the simulated values. The experimental values for 2mm sample are more erratic than in the other two samples where curves are much smooth.

It can be seen that the maximum absorption is achieved at a much high frequency of well over 6000Hz while in the 5mm and 10mm sample maximum absorption is at a lower frequencies of about 2500Hz and 2000Hz respectively. Generally there is close match of simulated and experimental results. Figure 3.8: Absorption coefficient for single fibre C3 curves 4.3.2 Absorption coefficients for Double C3 Figure 3.9 shows the results that involved using two pieces (double) of the fibre C3 sample.

...Download file to see next pages Read More
Tags
Cite this document
  • APA
  • MLA
  • CHICAGO
(Vehicle Interior Noise Prediction By Using Experimental Methods And Thesis Example | Topics and Well Written Essays - 8000 words - 1, n.d.)
Vehicle Interior Noise Prediction By Using Experimental Methods And Thesis Example | Topics and Well Written Essays - 8000 words - 1. https://studentshare.org/engineering-and-construction/2068335-vehicle-interior-noise-prediction-by-using-experimental-methods-and-analysis
(Vehicle Interior Noise Prediction By Using Experimental Methods And Thesis Example | Topics and Well Written Essays - 8000 Words - 1)
Vehicle Interior Noise Prediction By Using Experimental Methods And Thesis Example | Topics and Well Written Essays - 8000 Words - 1. https://studentshare.org/engineering-and-construction/2068335-vehicle-interior-noise-prediction-by-using-experimental-methods-and-analysis.
“Vehicle Interior Noise Prediction By Using Experimental Methods And Thesis Example | Topics and Well Written Essays - 8000 Words - 1”. https://studentshare.org/engineering-and-construction/2068335-vehicle-interior-noise-prediction-by-using-experimental-methods-and-analysis.
  • Cited: 0 times

CHECK THESE SAMPLES OF Vehicle Interior Noise Prediction by Using Experimental Methods and Analysis

Adapting Krmn Vortex Street Phenomena to the Reduction of Induced Drag in Aerospace Vehicles

Naturally, the overall aerodynamic and flight stability characteristics of aeronautical vehicles remain the same as the same set of governing equations are applied in the designing and analysis phase.... The conclusion will be strengthened with data as well as original solution methods which will be introduced in this thesis.... Karman Vortex Street Phenomena will be examined in detail and then with corresponding experimental and computational data, the thesis will show that the application of multiple wingtip feathered winglets will have a measurable effect in reducing the overall drag and hence the overall fuel cost of the aerospace vehicle....
17 Pages (4250 words) Thesis Proposal

Characterization of the Automotive Interior Cabin Noise

hellip; The interior design of a vehicle is the major factor that determines the interior noise and vibrating levels whereby the interior design will either keep these levels to a minimum or accelerate the noise and vibrating levels.... Consequently, interior trims such as the car-seats and roof covering play a very vital role in the observation of interior noise and vibrations specifically in relatively heightened frequencies (>400Hz).... Although, the frequency at which the highest level of noise is experienced normally depends on the size of the car, the corresponding interior noise spectra for all personal vehicles as investigated by Jha and Priede are all alike....
6 Pages (1500 words) Research Proposal

Organizing PhD Thesis

using a comparison, the New European Driving Cycle (NEDC) was taken as the basic framework for testing.... This paper attempts to quantify the relationship between vehicle fuel emissions and the various factors that contribute to it such as speed, The central contention was to come up with a mathematical model that could be used to reliably tabulate the fuel consumption of a passenger vehicle....
18 Pages (4500 words) Literature review

Characterization of the Automotive Interior Cabin Noise: Interior Trim Acoustic Materials

The interior design of a vehicle is the major factor that determines… he interior noise and vibrating levels whereby the interior design will either keep these levels to a minimum or accelerate the noise and vibrating levels.... n carrying out this research we first have to understand the effects of vehicle interior trims in minimizing interior cabin noise.... They are working tirelessly to ensure that these noise and vibrating levels are kept to a minimum....
6 Pages (1500 words) Research Proposal

Validation of Vehicle Fuel Consumption

using a comparison of different driving cycles, the New European Driving Cycle (NEDC) was taken as the basic framework for testing.... This paper attempts to quantify the relationship between vehicle fuel emissions and the various factors that contribute to it such as speed, acceleration, throttle position etc.... nbsp;… The central contention was to come up with an empirical correlation that could be used to reliably tabulate the fuel consumption of a passenger vehicle....
140 Pages (35000 words) Essay

Automotive Systems Principles

nbsp;… Optimizing the torque of the vehicle engine is a very critical factor that designers consider since it significantly influences the vehicle's acceleratory performance (Ahmadi, 2007).... Optimizing the torque of the vehicle engine is a very critical factor that designers consider since it significantly influences the vehicle's acceleratory performance....
7 Pages (1750 words) Assignment

The Potential of Hydrogen Fueled Vehicle in Agriculture

The author of the paper "The Potential of Hydrogen Fueled vehicle in Agriculture" argues in a well-organized manner that by 2030, greenhouse gasses discharge from developing countries could represent the greater part of the world CO2 releases (European Commission 2003).... nbsp;… The energy demand is rising at a rapid rate....
46 Pages (11500 words) Thesis

Development of a Smartphone App for Vehicle Squeak and Rattle Noise

"Development of a Smartphone App for Vehicle Squeak and Rattle noise" paper gives a literature review on various pieces of literature concerning the same topic under discussion.... Manufacturers are considering solving this problem of noise caused by S & R in some ways....
21 Pages (5250 words) Research Proposal
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Contact Us